 | The University of Virginia record February 1, 1918 |  |
COURSES OF INSTRUCTION.
The Subjects of Instruction in Engineering are grouped into ten classes,
each designated by a distinctive number for each term, the lecture and laboratory
courses being likewise differentiated. This grouping follows the arrangement
shown below:
| Mathematics | 100 to 199 |
| Physics | 200 to 299 |
| Chemistry | 300 to 399 |
| Geology and Mining | 400 to 499 |
| Mechanics | 500 to 549 |
| Experimental Engineering | 550 to 599 |
| Drawing and Shop-work | 600 to 699 |
| Civil Engineering | 700 to 799 |
| Mechanical Engineering | 800 to 899 |
| Electrical Engineering | 900 to 999 |
Lecture courses are listed in the first fifty numbers of all classes; laboratory
or practice courses are listed in the second fifty numbers of all classes.
The same numbers are used in all schedules of lecture hours, laboratory periods
and examination days.
MATHEMATICS.
Professor Echols.
Professor J. M. Page.
Adjunct Professor Luck.
Mr. Briggs.
Freshman Mathematics. [Page and Luck.]
8:30-9:30, M. W. F.
100. Trigonometry.
A complete course in plane and spherical trigonometry is pursued with
constant drill in the solution of problems, and exercises in the use of logarithms.
(Fall.)
101. College Algebra.
The work begins with the progressions and proceeds with the study of
the binomial formula, of the convergence and divergence of series, and of the
binomial, exponential and logarithmic series. The study of inequalities and
determinants prepares for the theory of equations, with which the course is
closed. (Winter.)
102. Analytical Geometry.
In this elementary course the study of Cartesian and polar coördinates is
followed by numerous exercises on the graphical representation of equations.
Special attention is given to the straight line and the representation of the
general equation of the first degree in two variables. The course is intended to
prepare for the fuller study of the analytical geometry of the conic sections.
(Spring.)
Sophomore Mathematics. [Echols.]
11:30-12:30, M. W. F.
103. Conic Sections.
This course in analytical geometry reviews the topics of Course 102 and
completes the study of the conic in its particular and general forms. A brief
examination of curves referred to polar coördinates is then followed by the
special study of a number of classical curves. (Fall.)
104. Differential Calculus.
The differential calculus is expounded and illustrated by exercises in the
expansion of functions, evaluation of indeterminate forms and problems of
maximum and minimum for functions of one variable. The method is then
applied to the geometry of curves, tangencies, curvature, envelopes and curve
tracing. (Winter.)
105. Integral Calculus.
The integral calculus is taken up; the integral is defined, and exercises in
elementary integration prepare for the application to numerous problems in
lengths, areas and volumes. When time permits, a brief introduction to ordinary
differential equations will be given. (Spring.)
PHYSICS.
Professor Hoxton.
Associate Professor Sparrow.
Mr. Hiden.
Mr. Nalle.
200-201-202. General Physics. [Hoxton.]
10:30-11:30, T. Th. S.
The elements of mechanics, sound, heat, electricity and magnetism, and
light. Instruction is given by lectures, textbooks, recitations, and problems,
with experimental demonstrations. (Fall, Winter, Spring.)
203-204. Electricity and Magnetism. [Hoxton.]
8:30-9:30, T. Th. S.
The elements of the mathematical theory and an introduction to modern
ideas of electricity are given. (Fall and Winter.)
250-251-252. General Physics Laboratory. [Sparrow and Assistants.]
9:30-11:30 or 2:30-4:30, M. W. F.
This course accompanies 200-1-2. Emphasis is laid upon fundamental
principles and the phenomena which underlie engineering problems. Written
reports of laboratory work are required. Problem work and oral recitation on
Friday. (Fall, Winter, Spring.)
253-254. Electricity and Magnetism Laboratory. [Hoxton.]
2:30-4:30, T. Th.
This course accompanies 203-4. Emphasis is laid upon methods of standardizing
and experimental studies in the behavior and underlying principles of
measuring instruments and other electric apparatus. (Fall and Winter.)
CHEMISTRY.
Professor Dunnington.
Professor Bird.
Adjunct Professor Venable.
Adjunct Professor Freas.
Mr. Cannon.
Mr. Easterwood.
Mr. Franke.
Mr. Leach.
Mr. Pinner.
Mr. Swift.
300-301-302. General Chemistry. [Bird.]
9:30-10:30, T. Th. S.
The fundamental principles and phenomena of inorganic, organic and
physical chemistry are discussed, and the foundations of analytical chemistry
are dealt with at appropriate places. The time is mainly devoted to inorganic
phenomena. No previous study of chemistry is demanded. (Fall, Winter,
Spring.)
303-304-305. Physical Chemistry. [Freas.]
10:30-11:30, T. Th. S.
The calculus is required, and previous training in physics is desirable. This
course will include work upon such topics as the gas laws, the kinetic theory
of gases, the properties of dilute solutions, osmotic pressure, the determination
of molecular weights, mass action, reaction velocity and equilibrium, electrolysis
and electrolytic dissociation, the phase rule, etc. General Chemistry and
Analytical Chemistry prerequisite. (Fall, Winter, Spring.)
309-310-311. Organic Chemistry. [Venable.]
8:30-9:30, M. W. F.
This course is intended to serve as an introduction to the general subject
of organic chemistry, including chemical synthesis and the theories of molecular
structure, as applied to the compounds of carbon. General Chemistry prerequisite.
(Fall, Winter, Spring.)
330-331-332. Analytical Chemistry B. [Dunnington.]
9:30-10:30, T. Th. S.
First term: Chemical manipulation and blowpipe analysis. Second term:
Inorganic qualitative analysis of ores of lead, gold and silver. Third term:
Practice in the analysis of salts, alloys and ores, and the examination of potable
water, coal, limestone, clay and so on, including simple quantitative determinations.
Weekly written exercises are required. (Fall, Winter, Spring.)
333-334-335. Analytical Chemistry C. [Dunnington.]
9:30-10:30, M. W. F.
After some training in manipulation and gravimetric estimations, the
class pursues volumetric estimations and a full course in quantitative analysis
of minerals, ores, coal, soil, iron and steel, technical products, and so on.
Weekly written exercises are required. As the student advances in the course
he is encouraged to undertake original research and assist in its prosecution.
(Fall, Winter, Spring.)
Laboratory Courses.
350-351-352. General Chemistry. [Bird and Instructors.]
11:30-1:30, M. W. F.
353-354-355. Physical Chemistry. [Freas.]
9 hours a week
359-360-361. Organic Chemistry. [Venable.]
2:30-4:30, M. W. F.
380-381-382. Analytical Chemistry. [Dunnington and Assistant.]
6 hours a week.
383-384-385. Advanced Analytical Chemistry. [Dunnington and Assistant.]
12 hours a week.
The Chemical Journal Club meets every other Thursday from 11 a. m.
to 12 m., for the critical review and discussion of various topics of interest
in current chemical literature, and of such chemical researches as may be in
progress in the University.
Advanced courses are given in Organic Chemistry (C2), and in Inorganic
Chemistry (D1). These courses are described in the General Catalogue,
and are recommended to all students of Chemical Engineering who
desire to prepare for the prosecution of research work.
GEOLOGY AND MINING.
Professor Watson.
Professor Thornton.
Mr. Holt.
[2] 400-401-402. Engineering Geology. [Watson.]
12:30-1:30, M. T. W.
A course of three lectures a week and three hours for private study.
Special emphasis is given to the study of common rock-forming minerals and
rocks, building stones and ores. The divisions of dynamical, structural and
physiographical geology are covered in considerable detail, and the practical
applications of the topics treated to engineering work are pointed out. (Fall,
Winter, Spring.)
403-404-405. Economic Geology. [Watson.]
11:30-12:30, M. T. W.
This course is designed to give a general but comprehensive account of the
origin, nature, distribution and uses of the metallic and non-metallic products
of the earth with especial reference to those of the United States. Lectures and
collateral reading six hours a week. (Fall, Winter, Spring.)
406-407-408. Petrography. [Watson.]
10:30-11:30, M. T. W.
This course aims to give a full knowledge of the determination of the
common rock-forming minerals and rocks in thin sections under the microscope.
It includes discussion of the microscopic structure, mineralogical composition,
genetic relations, and distribution of igneous, sedimentary, and metamorphic
rocks. Lectures and preparation to the amount of six hours per week.
(Fall, Winter, Spring.)
420-421-422. Mining. [Thornton.]
10:30-11:30, Th. F. S.
Mine surveying, exploitation of mines, mining machinery and the uses of
electricity in mining. (Fall, Winter, Spring.)
Laboratory Courses.
[3] 450-451-452. Engineering Geology. [Holt.]
6 hours a week.
453-454-455. Economic Geology. [Watson.]
6 hours a week.
456-457-458. Petrography. [Holt.]
6 hours a week.
MECHANICS.
Professor Thornton.
Freshman and Sophomore Mathematics and General Physics are prerequisite.
Free use is made of analytical geometry and the calculus; unprepared
students will not be registered for these courses.
Junior Mechanics. [Thornton.]
9:30-10:30, T. Th. S.
511. Theoretical Mechanics.
Fundamental principles of dynamics and the Newtonian laws of motion.
Statics of the material particle, of plane laminæ, of rigid bodies, and of elastic
solids; centres of gravity; equilibrium of rigid bodies and of material systems.
Dynamics of the particle; uniform and uniformly varied motion; harmonic
motion; meteoric motion; pendulum motion. Dynamics of the rigid body;
moments of inertia; rotating and revolving solids; laws of work and energy;
impact and collision. (Fall.)
512. Strength of Materials.
Fundamental laws of stress and strain in elastic solids. Strength and
elasticity of rods, beams, and shafts. Reinforced concrete slabs and girders.
Deflection of simple and restrained beams, and of continuous girders. Strength
of columns under both axial and eccentric loads. Strength of ties and struts
under lateral loads. (Winter.)
513. Hydrostatics and Hydraulics.
Fundamental laws of fluid equilibrium. Application to the analysis of
water tanks, boiler shells, thick pipes, reservoir dams, and weirs. Principles of
the motion of fluids; application to efflux from orifices and weir notches, flow in
pipes and canals, and gauge measurements of canals and rivers. Principles of
linear and angular momentum; applications to the analysis and design of
turbines and pumps. (Spring.)
Senior Mechanics. [Thornton.]
9:30-10:30, M. W. F.
514. Mechanics of Machines.
General mechanical principles illustrated in the action of machines. Analysis
of machines and the relative motions of their elements. Friction in machines.
Static equilibrium of machines. Transmission of power in machines. Regulators
and governors. Balance of machines. Brakes and dynamometers. Loads
and inertia forces. (Fall.)
515. Stability of Structures.
Framed structures under dead and live loads; applications to cantilever
bridges, draw bridges, and truss deflections. Statically indeterminate structures;
application to mill buildings, suspension bridges, and arched bridges.
Earth pressure, retaining walls, and foundations. (Winter.)
516. Hydraulic Motors and Pumps.
Water wheels, reaction turbines, and impulse turbines. Centrifugal pumps
and turbine pumps. Reciprocating pumps, pumping mains, and hydraulic transmissions
of power. (Spring.)
EXPERIMENTAL ENGINEERING.
Adjunct Professor Lapham.
Mr. Brown.
The courses are principally conducted in the laboratories, but lectures are
given to explain the manufacture of materials, the design and operation of
equipment, methods of testing, and the reasonable interpretation of the results.
550. Road Materials Testing. [Lapham and Assistant.]
2:30-4:30, M. W. F.
Samples of stone are tested for specific gravity, absorption, cementing
value, toughness, resistance to abrasion, and compressive strength. Asphalts
and tars for specific gravity, penetration, melting point, volatilization, viscosity,
fixed carbon, etc. (Spring.)
560. Structural Materials Testing. [Lapham and Assistant.]
9:30-12:30, 2:30-4:30, W. F.
Standard tests for Portland cement; tests of fine and coarse aggregates;
proportioning of concrete by sieve analysis and Fuller's curve; compression
tests of cement, mortar, and concrete; tension, compression, and torsion tests
of metals; transverse tests of timber and cast iron; autographic testing. The
Standards of the American Society for Testing Materials are used as a guide
and reference. (Fall.)
561. Structural Materials Testing. [Lapham and Assistant.]
9:30-12:30, W. or F.
This course is similar to Engrg. 560, but is arranged to cover part of
the work in a shorter time. (For Electrical and Mechanical Engineers.)
(Fall.)
570. Fuel and Oil Testing. [Lapham and Assistant.]
9:30-12:30, 2:30-4:30, W. F.
Standard methods for sampling coal; determination of the heating value
of coal by the bomb calorimeter, with a study of the cooling correction; proximate
analysis of coal; the heating value of gas by the Junker calorimeter;
determination of viscosity, flash point, chill point, and specific gravity of oils;
the coefficient of friction for lubricants. (Winter.)
571. Fuel and Oil Testing. [Lapham and Assistant.]
9:30-12:30, W. or F.
This course includes the tests for oil given in Engrg. 570, and a brief study
of coal testing. (For Civil Engineers.) (Winter.)
580. Hydraulic Testing. [Lapham and Assistant.]
9:30-12:30, 2:30-4:30, W. F.
The measurement of the flow of water by standard orifices and weir
notches; calibration of a piston meter; tests of the Venturi meter; determination
of the coefficient of friction for pipe and pipe elbows; economy and
capacity tests of pumps. (Spring.)
590. Power Testing. [Lapham.]
10:30-1:30, Th. S.
The calibration and adjustment of gauges; calibration of thermometers,
planimeters, and indicators; valve setting; determination of clearances; flue
steam engine; tests of a gasoline engine; test of the University Power Plant
boilers. (Fall.)
591. Power Testing. [Lapham.]
10:30-1:30, Th. S.
This course is a continuation of Engrg. 590. Complete test of a steam
engine; guarantee test of a steam turbine with method for correcting to
standard conditions; turbine tests; tests of an air compressor; tests of a
centrifugal blower. The Power Test Code of the American Society of Mechanical
Engineers is used throughout. (Winter.)
Thesis. [Lapham].
Advanced work in the testing of materials and equipment is offered to men
who are considered competent to undertake it. The work is largely independent
and may be substituted for the thesis.
Engineering Reports. [Lapham.]
Instruction is given in the arrangement of material, its presentation by
tables and curves, and in computing with the slide rule and by logarithms.
Preliminary reports are required for each separate test. The final report covers
a series of tests corresponding to the usual commercial or research investigation,
and must meet the standards of professional practice.
DRAWING.
Professor Thornton.
Professor Hancock.
Mr. Henderson.
Mr. Stuart.
Freshman Drawing: Lecture Courses.
600. Practical Geometry. [Thornton.]
12:30-1:30, T. Th.; 8:30-9:30, S.
Fundamental problems of plane geometry with applications to the mensuration
of rectilinear and curvilinear figures; conic sections and the methods of
constructing these curves; the orthographic projection of polyhedra and of the
three round bodies in erect and oblique positions; sections of curved surfaces by
planes and intersections; the mensuration of solids and Simpson's rule; the
graphical solution of equations; and the theory and use of the Polar Planimeter.
(Fall.)
601. Machine Construction. [Hancock.]
8:30-9:30, T. Th. S.
Study of the hand and machine tools in the wood and machine shops, their
functions, construction, and operation; free-hand sketching of machine parts;
elementary problems in the computation of shafting, belting, rope drives, toothed
gears, etc. Problems are assigned the student to guide him in the study of each
machine. (Winter.)
Freshman Drawing: Practice Courses. [Henderson.]
9:30-11:30, M. W. F.
Each student executes one finished plate 15″×20″ weekly. These plates
are drawn under the supervision of the instructor and must be neatly finished,
lettered and dimensioned. Every student is required to make tracings and
blueprints of a certain number of his own plates.
650. Mechanical Drawing.
This course embraces training in technique, practice in lettering, and the
graphical solution in the weekly plates of a series of problems in practical plane
and solid geometry, and in graphical algebra and trigonometry. (Fall.)
651. Machine Drawing.
Finished plates consisting of detailed working drawings of machine parts.
The drawings are made, in part, from free-hand sketches from the machine
itself, and, in part, from designs and specifications worked out by the student.
(Winter.)
[4] 652. Topographical Drawing.
In this course the conventional methods of making topographical maps
are carefully taught. Each student is required to become reasonably proficient
in the preparation of such maps. Particular attention is paid to the study of
contoured plans and the solution of problems based on them. The associated
lecture and field courses are 700 and 750. (Spring.)
Sophomore Drawing: Lecture Courses.
12:30-1:30, M. W. F.
603. Graphical Statics. [Thornton.]
The necessary preparation is such knowledge of experimental mechanics as
is given in Physics 200. Graphical methods in mechanics; problems in the
composition and resolution of forces and moments; determination by graphical
methods of centers of gravity, and moments of inertia; construction of strain
sheets for the simpler forms of roof and bridge trusses; study of the stability
of dams and walls; calculation of internal stress in girders, and beam deflections.
(Fall.)
604. Descriptive Geometry. [Thornton.]
The fundamental problems on the point, line, and plane are carefully
studied, with applications to the construction of shadows on polyhedra and to
the graphical statics of force-systems in three dimensions. The projections,
tangencies, sections, and intersections of curved surfaces are then taken up, with
applications to the determination of shades and shadows on such surfaces.
The course concludes with an elementary theory of linear perspective.
(Winter.)
605. Structural Design. [Thornton.]
Graphical analysis and design of simple beam bridges; of reinforced
concrete slabs and beams; of plate girders; of retaining walls for earth; and
of simple types of framed structures. Special attention is given to the structures
important in highway engineering. (Spring.)
Sophomore Drawing: Practice Courses. [Stuart.]
11:30-1:30, T. Th. S.
The work of the course is the execution each week of a plate 15″×20″,
under the direction of a competent instructor. The problems assigned are such
as serve to illustrate the topics discussed in the associated lecture-courses and
develop power in the use of graphical methods. Each student is required also
and to use the planimeter for the mensuration of areas and volumes bounded
by curved lines and surfaces.
653. Graphical Statics.
Fall.
654. Descriptive Geometry.
Winter.
655. Structural Drawing.
Spring.
SHOP-WORK.
Professor Hancock.
Mr. Crickenberger.
Mr. Livesay.
Mr. Wise.
Shop Instruction is given for its educational value. The purpose of this
Department is to train engineers, not artisans; and the claims of the shops
are not permitted to infringe on the more vital functions of the laboratories,
the drafting rooms, and the lectures.
Courses 660, 661 are required of all students of engineering; 662, 663 of
students of mechanical and electrical engineering; 664, 665 of mechanical engineering
students only.
660. Freshman Wood Shop. [Wise.]
3 hours a week.
Bench exercises in sawing, planing, boring, chiseling, tool sharpening.
Lathe exercises in turning between centers and on a face plate.
Machine-tool exercises in the production of useful articles. (Fall or Winter.)
661. Freshman Machine Shop. [Hancock and Assistants.]
3 hours a week.
Bench exercises in chipping and filing.
Engine-lathe exercises in turning, boring, and thread cutting.
Machine-tool exercises in drilling, planing, shaping, and milling.
(Fall or Winter.)
662. Sophomore Machine Shop and Forge Shop.
[Hancock and Assistants.]
6 hours a week.
Bench and machine-tool work in the construction of articles of commercial
value. Exercises in forging iron and steel; forging and tempering center
punches, cold chisels, lathe and planer tools. (Fall.)
663. Sophomore Pattern-making and Foundry. [Wise.]
6 hours a week.
Simple solid and split patterns and core boxes; core making, moulding and
casting. (Spring.)
664. Senior Machine Shop. [Hancock.]
6 hours a week.
In this course the student is given the opportunity to construct some useful
machine. This session the class is building a piece of apparatus for the testing
laboratory. (Fall.)
665. Senior Machine Shop. [Hancock.]
6 hours a week.
Exercises in tool making and tempering; jig making; precision methods
in machine-tool work. (Winter.)
CIVIL ENGINEERING.
Professor Newcomb.
Mr. Brown.
Mr. Carroll.
Mr. Clark.
[5] 700. Plane Surveying. [Newcomb.]
8:30-9:30, T. Th. S.
Lectures on the theory, uses, and adjustments of the compass, level, transit,
and stadia; the computations of surveying; the methods and proper conduct
of land, mine, city, topographic, and hydrographic surveys. Practical class
exercises illustrating the subject matter of the lectures are assigned to the
students throughout the entire course. (Spring.)
701. Curves and Earthwork. [Newcomb.]
8:30-9:30, Th. F. S.
Lectures on simple, compound, transition and vertical curves; the form of
excavations and embankments, earthwork surveys, computation of volumes,
formation of embankments, computation of haul, cost of earthwork, blasting.
Practical exercises in map drawing and topography. (Winter.)
702. Railroad Engineering. [Newcomb.]
12:30-1:30, Th. F. S.
Lectures on reconnoissance and preliminary surveys, office location, field
location; the construction, maintenance and operation of railroads. Special
attention is given to questions of railway economics. (Fall.)
703. Roads; Streets; Street Railways. [Newcomb.]
12:30-1:30, Th. F. S.
Lectures on the principles of road location; the construction and maintenance
of earth roads, broken stone roads, gravel roads; the pavements for city
streets and sidewalks; the location and construction of street railways. (Winter.)
705. Short Span Bridges. [Newcomb.]
10:30-11:30, Th. F. S.
Lectures on the design and construction of standard types of steel and
timber bridges (Fall.)
706. Long Span Bridges. [Newcomb.]
10:30-11:30, Th. F. S.
Lectures on the design and construction of the more intricate single span
trusses, cantilever bridges, steel arches, continuous girders, and swing bridges.
(Winter.)
707. Waterworks and Sewers. [Newcomb.]
10:30-11:30, Th. F. S.
Lectures on the quality, sources, collection, conveyance, purification, and
distribution of city water supplies; the laws of flow in pipe lines and aqueducts;
the drainage of houses and streets; the collection and conveyance of sewage;
the disposal of sewage; the construction and maintenance of works. Practical
exercises in the design of pipe lines and sewers. (Spring.)
714. Materials of Construction. [Newcomb.]
12:30-1:30, Th. F. S.
A descriptive study of the materials used in engineering structures, together
with their characteristics and proper preparation. Lectures on the design and
construction of foundations for bridges and buildings. (Spring.)
718. Masonry Structures. [Newcomb.]
11:30-12:30, Th. F. S.
Lectures on the theory of reinforced concrete; the design and construction
of selected types of masonry structures. Practical exercises in design, together
with structural drawing. (Fall.)
[6] 750. Field Surveying. [Newcomb and Assistants.]
6 hours a week.
This course supplements 700, Plane Surveying, and consumes six hours
a week throughout the Spring Term of the Freshman year. The student is
taught the use of the chain, tape, compass, level, transit, stadia, and plane table.
The parallel work in the drawing-room (652) consists in making computations,
scale drawings, profiles, and contoured maps from notes taken in the field.
(Spring.)
751. Railroad Surveying. [Newcomb and Assistants.]
5 hours a week.
This course supplements 701, Curves and Earthwork. The class is divided
into squads, each squad making complete surveys, maps, profiles, and estimates
for a mile of located line. (Fall and Spring.)
755. Bridge Drafting. [Newcomb.]
12 hours a week.
This course accompanies 705, Short Span Bridges. Each student is required
to make complete design and detail drawings of one plate girder and one
selected type of short span bridge truss. (Fall.)
756. Bridge Drafting. [Newcomb.]
12 hours a week.
This course accompanies 706, Long Span Bridges. Each student is required
to prepare stress sheets and drawings for selected types of long span bridges.
(Winter.)
MECHANICAL ENGINEERING.
Professor Hancock.
800. Elementary Steam Engineering. [Hancock.]
8:30-9:30, M. W. F.
A study of commercial fuels and their uses in the production of power;
of the properties of steam and the methods of measuring pressure, temperature
and humidity; of the design and construction of steam boilers, chimneys, superheaters,
economizers, feed-water heaters and condensers; of the steam engine,
steam turbine, pumps and injectors. Weekly problems for private solution.
(Fall.)
801. Steam Power Plants. [Hancock.]
8:30-9:30, M. W. F.
The economic design and operation of steam power plants. The subject is
treated in lectures with assigned reading. Each student is expected to produce
during the term a complete design of a plant to satisfy assumed conditions.
(Winter.)
802. Machine Design. [Hancock.]
8:30-9:30, M. W. F.
Straining actions in machine elements; friction and lubrication; riveted
fastenings, screws and screw fastenings; keys, cotters, and forced fits; axles,
shafting and couplings, journals and bearings; belt and rope transmissions;
toothed gearing. Weekly problems for private solution. (Spring.)
803. Internal Combustion Engines. [Hancock.]
10:30-11:30, M. W. F.
A study of the thermal problems of internal combustion engines, gas producers,
air compressors and motors and hot air engines. Weekly exercises and
problems. (Fall.)
804. Steam Engines and Steam Turbines. [Hancock.]
10:30-11:30, M. W. F.
A study of the thermal problems of steam engines, steam turbines and
refrigerating machinery. Weekly exercises and problems. (Winter.)
805. Engine Design. [Hancock.]
10:30-11:30, M. W. F.
A study of the mechanical problems involved in the design of machines
discussed in the two previous courses; inertia effects, stresses, strength of parts,
balancing, governing, etc. Weekly exercises and problems. (Spring.)
806. Kinematics of Machines. [Hancock.]
12:30-1:30, M. W. F.
A study of the applications of plane, spheric and screw motions in machines.
The course is principally devoted to valve gears, straight line motions, cams,
toothed wheels, and screw gears. Graphic methods are employed and the work
is almost wholly on the drawing board. (Winter.)
[7] 807. Locomotive Engineering. [Hancock.]
12:30-1:30, M. W. F.
A study of the steam locomotive. The problems of inertia effects, balancing,
tractive force, track and train resistances, hauling capacity, etc., are
treated in lectures. Clear physical conceptions are gained by careful examination
and study of the machine itself. For a knowledge of its history and
present development, general reading and written reports are required. (Fall.)
[8] 809. Automobile Construction. [Hancock.]
12:30-1:30, M. W.
A study of the engine, including details of construction, ignition, combustion
and balancing; of the transmission, running gear and control; of electric
starting and lighting systems. The course is conducted by lectures, with
assigned reading and shop-work in taking down, reassembling and testing an
automobile. See Course 859 below for the practice. (Fall.)
[9] 859. Automobile Laboratory. [Hancock.]
11:30-1:30, F.
This course supplements 809, and is devoted to the testing and work upon
automobiles. (Fall.)
ELECTRICAL ENGINEERING.
Professor Rodman.
Mr. Wolcott.
900. Elements of Electrical Engineering. [Rodman.]
10:30-11:30, T. Th. S.
Lectures treating fundamental principles of Electrical Engineering; basic
ideas and fundamental units discussed; magnetic circuits and continuous electric
currents treated in detail; electromagnetism carefully studied. Special attention
is given to the physical conceptions involved, and numerous assigned problems
exemplify and broaden the theoretical discussions. Problem hour weekly,
11:30-12:30, Th. (Fall.)
901. Direct Current Machines. [Rodman.]
10:30-11:30, T. Th. S.
Lectures on the theory, construction, characteristics, and operation of direct
current generators and motors and the accessory apparatus required for the
proper management and control of these machines. The principles of testing
such machines are carefully discussed. Problems illustrating the methods of
calculation involved in continuous current circuits and practical examples from
standard engineering practice form an important part of the work. Problem
hour weekly, 11:30-12:30, Th. (Winter.)
902. Periodic Currents. [Rodman.]
10:30-11:30, T. Th. S.
Lectures on electrostatic phenomena, variable currents, alternating currents,
and alternating current circuits, both single and polyphase. A careful study is
made of circuits with periodic currents and their characteristics when resistance,
Extensive problem work is required to facilitate the treatment of simple
and complex circuits. Problem hour weekly, 11:30-12:30, Th. (Spring.)
903. Alternating Current Machinery. [Rodman.]
10:30-11:30, M. W. F.
Lectures on the theory, construction, characteristics, and operation of alternating
current generators, synchronous motors, rotary converters, and transformers.
These machines are considered as units and as integral parts of
electrical systems. The principles of testing such apparatus under various conditions
of loading are discussed, and assigned problem work illustrates the
theory and practice. Problem hour weekly, 11:30-12:30, F. (Fall.)
904. Alternating Current Machinery. [Rodman.]
10:30-11:30, M. W. F.
This course is a continuation of 903. The lectures treat more particularly
alternating current motors, induction, series and repulsion types, with their
characteristics and control apparatus. Methods of testing are outlined and
graphical methods of calculation and predetermination of operating characteristics
are discussed. Problems taken from engineering practice serve to broaden
and fix the theoretical deductions. Problem hour weekly, 11:30-12:30, F.
(Winter.)
905. Electric Power Transmission. [Rodman.]
10:30-11:30, M. W. F.
Lectures on systems of transmission and distribution, with a detailed consideration
of the electrical characteristics of transmission lines; the electrical
equipment of stations and sub-stations, including generating apparatus, switchboards,
control systems and protective devices; systems of transformation and
the economic considerations which influence the design of the complete electrical
system. Problem hour weekly, 11:30-12:30, F. (Spring.)
906. Illumination and Photometry. [Rodman.]
8:30-9:30, M. W. F.
Lectures on light, its physical properties; illuminants and their characteristics;
shades and reflectors; photometry, standards and apparatus; illumination
calculations for point and surface sources; principles of interior, exterior,
decorative, and scenic illumination. Problems illustrating computations necessary
for the consideration of the Illuminating Engineer are assigned. (Fall.)
907. Electric Traction. [Rodman.]
8:30-9:30, M. W. F.
Lectures on the various types of electric motors for traction purposes, controllers
and systems of control, brakes, rolling stock, track, train performance,
and electric railway economics. A discussion with problems of the complete
electrification system for electric railways, including generating apparatus, transmission,
sub-stations and equipment, distribution, and utilization of electrical
energy for car propulsion. (Winter.)
910. Direct Current Systems. [Rodman.]
8:30-9:30, T. Th. S.
Lectures dealing with the fundamentals of electrical circuits and direct
current machinery. Problem work accompanies the lectures. The course is
essentially for the non-electrical engineering students. (Fall.)
911. Alternating Current Systems. [Rodman.]
8:30-9:30, T. Th. S.
Lectures covering the fundamentals of alternating current circuits and
machinery. Brief expositions of the subjects of electric lighting and power
fundamentals. For non-electrical engineering students. (Winter.)
[10] 912. Electrical Equipment. [Rodman.]
8:30-9:30, T. Th. S.
Lectures and computations dealing with the choice, arrangement, and systems
of wiring and control governing the approved methods of installation of
electrical equipment for industrial uses. For non-electrical engineering students.
(Spring.)
[11] 920-921-922. Wireless Telegraphy and Signaling. [Rodman.]
11:30-12:30, S.
A course of lectures once a week dealing with the theory and operation of
wireless telegraph installations, and standard methods of signaling, with particular
reference to their use in war. The lectures are supplemented by practice
in code sending and receiving by various methods, see 970-1-2. (Fall, Winter,
Spring.)
941. Engineering Economics. [Rodman.]
8:30-9:30, M. W. F.
Lectures and parallel reading on the economic considerations involved in
engineering problems. Optional course. (Spring.)
950-951-952. Direct Current Laboratory. [Rodman.]
11:30-1:30 and 2:30-4:30, M.
This course supplements 900-1. The laboratory work is devoted to a study
of electrical instruments, their use and manipulation; simple electrical circuits
and study of direct current apparatus and its operation; characteristics of
generators and motors. (Fall, Winter, Spring.)
953-954-955. Alternating Current Laboratory. [Rodman.]
11:30-1:30 and 2:30-4:30, W.
This course supplements 902-3-4, dealing with measuring instruments for
alternating current circuits; series and parallel circuits and their characteristics;
polyphase circuits, balanced and unbalanced; and alternating current
generator, motor and transformer characteristics. (Fall, 4 hours a week;
Winter, 6; Spring, 4.)
956. Photometric Laboratory. [Rodman.]
11:30-1:30, T.
This course accompanies 906. Photometric tests are made upon different
types of incandescent lamps. The operating characteristics of incandescent and
arc lamps are studied. Tests of illumination, interior and exterior, are carried
out. Study of photometric standards and devices. (Fall.)
[12] 960-961-962. Electrical Laboratory. [Rodman.]
2:30-4:30, T. Th.
This course supplements 910-11-12. The work of the first term is devoted
to direct current tests; the second term exercises are on alternating current
circuits and machines; the course in the third term is largely concerned with
calculations and drawings for typical industrial equipments of electrical machines
and controls. (Fall, Winter, Spring.)
[13] 970-971-972. Signaling Laboratory. [Wolcott.]
6 hours a week.
This course supplements 920-1-2. The greater part of the time is devoted to
practice in code receiving and sending by wireless telegraphy. Some time is
devoted to other standard methods of communication. (Fall, Winter, Spring.)
The University of Virginia branch of the American Institute of Electrical
Engineers holds regular meetings for the discussion of periodical literature and
the exposition by resident and visiting engineers of present-day problems in
Electrical Engineering.
| The University of Virginia record February 1, 1918 | |